<th id="96fg9"></th>
  • 網站公告:

    產品中心

    濟南精拓流體設備有限公司

    電話:0531-69951198

    郵箱:jingtuolt@163.com

    傳真:0531-69951198

    地址:濟南市歷城區西周南路9號

    網址:http://www.k30628.cn

    常見問題

    當前位置:首頁 - 新聞中心 - 常見問題 - 氣動增壓泵和氣體增壓泵選

    氣動增壓泵和氣體增壓泵選型的區別

    發布時間:2017-12-18 17:35:42   發布人:http://www.k30628.cn
      根據系統所需壓力初步確定泵的型號。一般地,SC的氣動增壓泵的驅動氣壓≤7bar。所以,增壓比Ratio=Po/Pa。其中,Po是系統的輸出壓力;Pa是氣動泵的驅動壓力。

      The model of the pump is preliminarily determined according to the pressure required by the system. In general, SC pneumatic driven pressure booster pump is less than or equal to 7bar. So, the turbocharging is more than Ratio=Po/Pa. Among them, Po is the output pressure of the system; Pa is the driving pressure of the pneumatic pump.

      一般取最大值0.7MPa。根據計算出來的增壓比,在相應類型的泵表中選擇型號。注意,通常我們會選擇增壓比略高于計算值的泵,以確保我們的泵在通常情況下都能輸出系統所需壓力。

      The maximum value of 0.7MPa is generally taken. According to the calculated turbocharging ratio, select the type in the corresponding type of pump table. Note that we usually choose slightly higher than the calculated value of the booster pump, the pump to ensure that we can output the required pressure system under normal conditions.

      增壓介質是空氣/氮氣,我們就在空氣增壓泵/氮氣增壓器中選.增壓介質是氣體,我們就在氣體增壓器中選;增壓介質是液體,我們就在氣動液體增壓泵中選。

      The pressurizing medium is air / nitrogen. We choose it in the air booster pump / nitrogen booster. The pressurizing medium is gas. We choose it in the gas supercharger. The pressurizing medium is liquid. We choose it in the pneumatic liquid booster pump.
    氣體增壓泵多少錢

      核算泵的流量是否滿足系統要求。當我們根據泵的出口壓力初步選擇了泵的型號后,我們需要核算改泵的流量是否滿足要求。

      Check the flow of the pump to meet the requirements of the system. When we choose the pump model according to the pressure of the pump, we need to check the flow rate of the pump to meet the requirements.

      如果流量不夠,那么,我們再選擇一個增壓比相近,流量比較大的泵,并核算流量,直到滿足系統流量要求為止。注意,我們所說的流量都是指常壓下的流量,即將1分鐘內經過泵增壓的介質(液體或氣體)放在常壓下去測量它的體積。

      If the flow is not enough, then we choose another pump with a supercharged ratio and a larger flow rate, and calculate the flow until the system flow requirements are met. Notice that what we mean by traffic is the flow rate under normal pressure, and it will be measured at 1 minutes if the medium (liquid or gas) pumped by a pump is placed at atmospheric pressure to measure its volume.

      根據增壓介質選擇泵的材質。經過上面3個步驟后,我們可以選出泵的基本型號了。然而,正確的型號還得考慮增壓介質對增壓泵材質的要求。

      Select the material of the pump according to the supercharging medium. After 3 steps above, we can choose the basic model of the pump. However, the correct model must also take into account the requirements of the pressurized medium for the material of the booster pump.

      本文的精彩內容來自氣體增壓泵詳細內容請點擊我們的官方網站:http://www.k30628.cn謝謝您的到來!

      The wonderful content of this article comes from the detailed content of the gas booster pump, please click on our official website: http://www.k30628.cn thank you for your arrival!

    13188935873

    qq

    2018正版梅花四字诗 绥滨县| 漯河市| 正蓝旗| 黄冈市| 秦皇岛市| 攀枝花市| 特克斯县| 奈曼旗| 临邑县| 汉沽区| 大冶市| 尼玛县| 张家川| 灵丘县| 德清县| 明溪县| 洱源县| 淮南市| 台北县| 莎车县| 新密市| 新绛县| 富蕴县| 南乐县| 阿巴嘎旗| 佳木斯市| 新化县| 乌审旗| 新田县| 延安市| 安仁县| 古浪县| 乌鲁木齐市| 南岸区| 墨玉县| 县级市| 慈利县| 佛山市| 陆良县| 山丹县| 益阳市| http://www.cha57.cn http://www.088success.top http://163.86e1g0.top http://m.tu66kk.top http://v.06z2m8.top http://v.lu56iu.top