<th id="96fg9"></th>
  • 網站公告:

    產品中心

    濟南精拓流體設備有限公司

    電話:0531-69951198

    郵箱:jingtuolt@163.com

    傳真:0531-69951198

    地址:濟南市歷城區西周南路9號

    網址:http://www.k30628.cn

    網站公告

    當前位置:首頁 - 網站公告 - 高壓空氣增壓泵安裝必備步

    高壓空氣增壓泵安裝必備步驟介紹

    發布時間:2018-01-04 16:13:39   發布人:http://www.k30628.cn
    1.高壓空氣增壓泵的安裝
    Installation of 1. high pressure air booster pump
    空氣增壓閥標配有兩個開槽安裝支架,增壓閥可以安裝在任意位置,推薦位置為垂直方向,每臺售出增壓閥都會附帶圖紙,標注所需的各種尺寸。
    The air booster valve is equipped with two slotting mounting brackets. The booster valve can be installed at any location, and the recommended position is vertical. Every booster valve will be attached with drawings, indicating the required sizes.
    2.預增氣源連接
    2. yejiyuzeng source connection
    高壓空氣增壓泵泵體上都標注“進口”,且圖紙上都標有端口尺寸及型號。預增氣體一定要純凈,氣體介質若有雜志可能會損壞高壓元件,導致增壓閥運行故障,所以建議大家在增壓閥進氣口安裝過濾裝置。
    The high pressure air pressurized pump body is marked "import", and the drawings are marked with the size and model of the port. By the gas must be purified, the gas medium if the magazine may damage the high-voltage components, leading to operational failure pressure increasing valve, it is recommended that you install filtering device in the booster valve inlet.
    3.氣源的連接
    Connection of 3. gas sources
    供氣回路的安裝時過濾/調壓閥需盡量開進增壓閥。進氣口端口為G1/4”,閥體上標注為”驅動氣口“,管徑為1/2”,如果管徑較小,增壓閥就不可以以最大流量運行。過濾調壓需按照名稱順序鏈接,靠近增壓閥。
    When the gas supply loop is installed, the filter / pressure regulating valve should be put into the pressurized valve as far as possible. The inlet port is G1/4, and the valve body is marked as a "drive air port" with a diameter of 1/2. If the pipe diameter is small, the booster valve can't run at the maximum flow rate. Filter pressure need to be linked in the name order, close to the turbocharger.
     氣體增壓泵
    4.消聲器
    4. muffler
    消聲器的使用時用來降低增壓閥運行時的噪音,保證運行環境的安靜。排氣口端口為G1/2”,標記為“出氣口”。
    The use of the muffler is used to reduce the noise of the operation of the pressurized valve, and to ensure the quiet of the operating environment. The port port is G1/2 ", marked as" air outlet ".
    5.高壓氣體出口的連接
    5. connection of high pressure gas outlet
    在增壓閥的配圖上標有端口尺寸及型號,增壓閥閥體上標注為“出口”,此為高壓出口,所以連接時需要特別謹慎小心,連接件需要大于最大輸出壓力。
    Port sizes and models in Figure booster valve superscript, booster valve on the valve body labeled as "export", this is the high pressure outlet, so the connection need to be cautious, connections need to be bigger than the maximum output pressure.
    6.高壓空氣增壓泵的啟動
    The start of 6. high pressure air booster pump
    ⑴在打開增壓閥的進氣開關之前,使用調節減壓閥將氣壓調到“0”PSI
    In the switch before the intake pressure valve, regulating valve pressure will be transferred to the "0" PSI
    ⑵確保所有的連接口及所有元件及安裝。
    The connection port and ensure all all the components and installation.
    ⑶將減壓閥緩慢調節至增壓閥開始啟動,正常情況下增壓閥在15-20PSI壓力下氣動。
    The valve will slowly adjust to the pressure valve is started, under normal circumstances, the pressure valve under the pressure of 15-20PSI pneumatic.
    ⑷完成1到3步驟后,調節泵的供氣氣壓直達到系統所需輸出壓力為止。
    The completion of the 1 to 3 steps, gas pressure regulating pump system to direct the desired output pressure.

    13188935873

    qq

    2018正版梅花四字诗 广宁县| 万山特区| 葫芦岛市| 锦屏县| 青冈县| 鄱阳县| 抚顺市| 闵行区| 门头沟区| 翼城县| 伊宁市| 巢湖市| 邵阳市| 华宁县| 东山县| 平果县| 西盟| 舞阳县| 乐安县| 阳信县| 吐鲁番市| 天镇县| 会宁县| 上蔡县| 甘南县| 屯门区| 监利县| 元阳县| 隆子县| 高陵县| 浦北县| 肃宁县| 夏邑县| 台山市| 台南县| 寿阳县| 崇义县| 保康县| 丽水市| 响水县| 芦溪县| http://www.able16h.site http://www.f770.cn http://www.111women.top http://www.k30125.cn http://www.ks422.cn http://www.an776.cn